I need to design a LED chaser that will be powered by a 12V battery. It needs to have a master PCB which will control all the slaves connected. The slaves will be chained together and distanced about 5 meters apart with a 4-pin connector IN and 4-pin connector OUT. Each slave will have a 12V lamp attached and switched by a mosfet. The requirement
Hi I need you to create 2 video of one 34 and one 60 sec similar to this one: [url removed, login to view] Do not copy the video or the scripts, it has to be original footage and scripting I'm attaching some images you cam use and you may add the Solara Light to any nice landscaping images similar to this website: [url removed, login to view] Please note it has to be private labeled ...
In a simple sapui5 app a js file has to be loaded at runtime. The content of ...file is saved in the backend via odata and fetched from the backend via odata. The service allready exist . Only create the app in eclipse or webide with js view and in the controller include the function via sap.ui.define. The file not staticly exist in the project tree.
programmer un pic16f19155 avec lcd , led et photodiode , le lcd doit afficher 3 chiffres et tres peu de texte
hello , I need someone who is based in malaysia to work with me on my project to control LED from computer , hardware part already purchased and now looking for someone who can work with to build UI and Chip controller programming so LED can be controlled by the computer (Wireless based). [REMOVED BY [url removed, login to view] ADMIN]
All About People is partnering with a large international manufacturer that is hiring a Controller in Manufacturing. For the right candidate, they would be getting in on the ground floor with an excellent opportunity at their first U.S. site. The company operates manufacturing plants in 6 countries. Lots of potential growth for the right candidate
Help me to setup a development environment using: Eclipse + FreeRTOS + My own code base + STM32F072 on Window10 (on Ubuntu is a must) This is a working project made by someone else and I just need to continue to develop it. I'm confortable with Linux C development but not Eclipse and Micro controllers.
...enough hours to get it finished off. What i'm trying to do is use a pass word protected web page to allow me to change/set darkness on/off levels, be able to set/adjust LED on delay time. LED Brightness, set turn on color/auto color change etc. also a setting to be able to send out to data to a raspberry pi that the light is active/connected and when motion
This project is to be completed in Kicad software; the schematic and pcb layout. It is a 300amp motor controller for 3 phase AC induction motor. The battery voltage will vary between 3volts and 25 volts. It must be able to operate all the way down to 3 volts! Some boost circuitry will need to be designed for gate drive. There will be 6 mosfets total
I need a CAN bus controller programmed, which controls an inverter. The Control unit needs to send approx 25 CAN bus ID's with around 100 - 150 signals at intervals between 10 ms and 1000 ms depending on the inputs. The code could be implemented in some standart CAN controller for automotive use. I am open to suggestions. Thanks
We are working on nexys video board and we are trying to access DDR3 memory using IPCORE in vivado design suite software. We want to read and write data into DDR3 memory using nexys video board.
...Information From LED. INTRODUCTION: Sending information from inside electronic gadget can be done through LED bulb. Reading the data in this case can be by photo sensor device. As the mobile is commonly used, using the light sensor of a mobile is targeted in this project. data through illumination The technique behind is by using LED light bulb's output
I need some help with selling something.
We have a temperature controller that we use for an egg incubator. It was developed for us several years ago and it is time to make some changes to the firmware. We have all of the original development files, but we are not programmers, so we are not able to do anything with them. For those of you who speak "code", you'll likely recognize and understand
My goal is to set up listings on Craig's list for different target markets. My listings will be in the Boat for sale section (I think) possible marine accessories 1) Title I will provide, 2) for location it must say the local market ie Chicago, Minneapolis, Ft Meyer... 3) I provide Price 4) I provide the complete description. and possible search words to be included. Finally: I will pr...
I need someone who can make a project with the help of pic micro controller [url removed, login to view] will use a smoke sensor and temperature sensor and detect the fire and turn the alarm on. urgent required. only serious bidder bid.
I am looking for a programmer to code my PIC microcontroller to drive a 6v dc motor using a PWM technique - The battery is in series - 3.6v x 2 = 7.4V LiPo 1000mAh The Motor Nominal voltage: 6VDC No-load speed: 13000rpm No-load current: 0.46A Stall torque: [url removed, login to view] Stall current: 11.8A The PWM technique should maintain the voltage at an average of 6V to the motor un...