Need someone who familiar in AVR-C connecting Bluetooth modules, SD card modules, Graphic LCD's and gyro module
I need you to develop some software for me. I would like this software to be developed for Windows using C or C++. Need to built an user interface for a microcontroller based articulated manipulator, there should be interlink of c,c++ (must) and/or Python(optional)
I need a basic firmware application for this microcontroller (STM32F048). I need a vendor class USB implemented, and an example of using SPI (Master mode) to communicate with a SPI slave device. Preferably using the DMA channels. Please read this description before placing a bid. I have included the STM32Cube setup of the board I have with this MCU
...Accuracy ±0.1° C Minimum Speed: 10 rpm (rotation speed change step| increment value) Time range: 1 second to 168 hours 3. GUI based control system with 5-inch width touch screen LCD display or phone screen with Remote Control. [virtual buttons and sliders (GUI)] 4. Color sensors will be installed on PCB Board. 5. User ID/Password set up. 6. The device
a smart reader system is programmable electricity...electricity readers units connected wifi to enable reading meters automatically with low cost and high accuracy. the system consists of 3-ph current sensors connected with a microcontroller system to manipulate and store the meter data. the total cost of electricity can be displayed in monitored
...%20M3 Inputs and Outputs must be able to source / sink 30VDC and all IO and power should be protected/isolated. Similar to this: [url removed, login to view] Schematic and board should be completed in either KiCAD or Eagle. Completed board will have screw terminals for IO and 24V power, and USB
...energy meters are compared so as to identify the theft status. Whenever there is discrepancy in the two values, a message that theft has occurred will be displayed in the LCD display as well as in the web page. We can access the web page from anywhere on the globe at any time using the consumer number provided by the supply authorities. So the
...and an ads1115 adc, which will have 4 channels each. The values of the two encoders and the eight analog channels will be displayed on both the android screen as well as the LCD. The esp32 will use Arduino code, while the host GUI will be an android app that controls each stm32 PWM for both duty and frequency. The app will record 100 points of each analog
Require a freelancer to write a code in C language for Digital Weigh Balance using ADUCM361 Microcontroller. Display on six- 7 Segments LCD. Features to be of standard digital balance. keyboard (5 keys), parameter setting, calibration, serial output, option to change parameter setting and calibration through serial communications as well.
I need someone to create a code for 16-Bit MCUs PIC24FJ256GA7 to communicate with LCD display and Keypad The keypad : [url removed, login to view] LCD : [url removed, login to view] I need someone who can test it and know it is working. provide the
This code uses the joystick and the display on the booster board to implement a driving game. A car is shown on the lower side of the display on a road. The player can use the joystick to direct the car to the right or left to avoid obstacles on the road. The player scores one point for passing each obstacle. Hitting any obstacle ends the game. The remainder of this document describes the game ope...
...to help us with a small project to develop a software for a microcontroller to comunicate with a Raspberry Pi. The Microcontroller shall performe some simple action to activate a Solenoid, led and a sensor. *** Scope overview *** 1. C/C++ programming for a STM32F030F4 Microcontroller (Slave). 2. Python programming for a Raspberry Pi 3 Model B
Micro-controller programming. The project involves reading weight load cells data and make simple calculations. Then present the data on LCD display. C/C++. Basic English. The salary for a monthly work is 10 000 PLN. The freelance is required to arrive to our R&D lab in Żyrardów (Near train station) for 4 weeks of project. Starting immediately
The project requires two mobile phones, one to control the robot that sends DTMF commands to another one mounted on the robot vehicle. A DTMF decoder interfaced with the microcontroller of 8051 families receives the commands and with the help of a motor driver operates the vehicle movement. Thus according to the commands sent from the phone two DC motors
Now i'm Working on PIC18F2550 Microcontroller for weather and farming sensors. I need experienced programmer to help for fetching sensors data and store in database using any programming language like python, Embedded c/c++, Hex .. Weather sensors: 1) Soil Temp: K type thermocouple 2) Humidity: DHT 22 + temperature 3) Rainfall: Reed switch