Pcb design jobs

Filter

My recent searches
Filter by:
Budget
to
to
to
Skills
Languages
Job State
8,659 pcb design jobs found, pricing in INR
Flex PCB design TR21 6 days left
VERIFIED

Design a TR21 flex PCB and output Gerber files and 3D PDF.

₹10576 (Avg Bid)
₹10576 Avg Bid
7 bids
Flex PCB design 6 days left
VERIFIED

Design a TR20 flex PCB and output Gerber files and 3D PDF.

₹10511 (Avg Bid)
₹10511 Avg Bid
9 bids

We would like to hire someone to design (no PCB needed, only schematic but the simulation needs to be as accurate as possible) a crystal notch at a specific frequency (in the MHz). We already have the quartz, we also have every parameters of each piece (Fs, Fp, Cs, Cp, Q, Rs ...) This filter needs to be matched at 50ohm IN and OUT. Attenuation

₹10208 (Avg Bid)
₹10208 Avg Bid
10 bids
PCB design 6 days left

I need a relatively simple PCB designing for a short POC run. The design is a 200 pin SO-DIMM socket with each pin tracked out to a pad large enough to solder by hand. It needs to be as small as possible while remaining usable.

₹5159 (Avg Bid)
₹5159 Avg Bid
4 bids

...experienced EU based PCB designer for the following "mSATA to USB 3.1 Type-C Adaptor (mass storage USB 3.1)" This is custom designed mSATA (SSD) to (Mass Storage) USB 3.1 (Type-C) adaptor. - Design based on ASMedia USB bridge are preferred - Design based on Texas Instruments USB bridge is the second preference - Maximum 4 layer ([url removed, login to view]...

₹60820 (Avg Bid)
Urgent NDA
₹60820 Avg Bid
6 bids

I need a simple 8 circuit common bus pcb designed. Each of the 8 common busses should have 18 holes that can accommodate 18AWG stranded wire. I'd also like there to be a test point for each of the 8 busses. The test points will need to be multimeter probe friendly so that a technician can plug one of the multimeter's probes in one test point and

₹1548 (Avg Bid)
₹1548 Avg Bid
27 bids

I am looking for an electronic engineer to design a circuit and making PCB for manufacture

₹7223 (Avg Bid)
₹7223 Avg Bid
13 bids

Hi, I have 3 PCB files that need modification in PADS. Changes have already been made in Altium for same PCB files, but i want same changes to be done in PADS.

₹8899 (Avg Bid)
₹8899 Avg Bid
17 bids

I would like to make a modular phone charger. If you have experience with PCB design and electronics feel free to respond! Please see attachment for requirements.

₹12317 (Avg Bid)
₹12317 Avg Bid
33 bids

Make a simple adapter board to split one power input into several high power lines.

₹2708 (Avg Bid)
₹2708 Avg Bid
7 bids

I need someone to either design a motherboard for me from scratch or work with the one that i have started designing in eagle. I would prefer the design to be made in eagle but other cad software's are OK too. the dimensions of the board should be in approximately a 2:1 ratio and can be any size smaller than 154/77mm. The board should be as thin

₹12897 (Avg Bid)
Guaranteed
₹12897 Avg Bid
2 entries

Hi, I have a project that needs to be done in Altium design...project that needs to be done in Altium designer. I will provide the schematic and BOM. You need to create the footprint library and layout and generate gerber once design is approved. I need design in 3 days (it's 4 layers board). If you have Altium designer experience, please let me know.

₹10511 (Avg Bid)
₹10511 Avg Bid
36 bids

We’re seeking a freelance writer to write articles to optimizing our website, everything is about PCB. Ideally, you’ve been writing professionally for at least 2 years, English is your native language. Also: 1). Above 400 words each article 2). 2 articles each day 3). Including 1 blog post and 1 web content 4). make your article as easily understood

₹6836 (Avg Bid)
₹6836 Avg Bid
34 bids

Design PCB. See attached block diagram. Super Bright 650nm LEDs, photodiode at 950nm, A/D conversion to suit to development board micro (STM32 nucleo, or similar). Engineers with 5 years minimum experience. Select components and be able to provide documented solution with limited input from me other than block diagram and information on the

₹1886 / hr (Avg Bid)
₹1886 / hr Avg Bid
29 bids

...Critique Small PCB Design Project Objectives: – Consultant to analyze and understand elements of a small PCB design – Consultant to provide recommendations as to the fitness of the designs and make suggestion for improvements of design and selected components. - Consultant shall provide feedback assessment and how to improve design for...

₹22055 (Avg Bid)
₹22055 Avg Bid
19 bids
Auto positioning sattellite 5 days left
VERIFIED

...of elements: 1 - automated signal source founder - pcb 2 - dishes (70 meter, etc) 3 - transponders 4 - red laser 5 - green Laser 6 - violet Laser 7 - solar panels 8 - accumulator 9 - automated light founder for panels - pcb 10 - router (IPs, MACs) - pcb 11 - list of sattellite ids - pcb 12 - hd lenses 13 - engines [url removed, login to view]

₹2386 (Avg Bid)
₹2386 Avg Bid
2 bids
Custom PoE board for Open Rov 4 days left
VERIFIED

I need custom PCB for charging batteries inside Open Rov (PoE cable) because they are discharging and I cannot dive infinitely. [url removed, login to view]

₹7094 (Avg Bid)
₹7094 Avg Bid
9 bids

Please Sign Up or Login to see details.

Featured Urgent Sealed

I need a design for my future product. It’s a heart monitor which is checking the heart’s activity during night. It is placed at the wrist and positioned on the opposite side where a watch is normally placed. The housing of this product will not have buttons, screen or any LED lights. The data gathered during the night will be send out to a phone app

₹1870 (Avg Bid)
₹1870 Avg Bid
17 bids

I am looking to make a b.o.m list for a circuit board design that I have. I currently don't have any b.o.m list for the design. I also need to slightly move two components on the pcb design.

₹7287 (Avg Bid)
₹7287 Avg Bid
22 bids