Camera Trigger System 2.0

Closed Posted Feb 28, 2013 Paid on delivery
Closed Paid on delivery

Stage 1. TRIGGER SYSTEM

We need a new way to trigger our cameras using arduino, raspberry PI or Beagleboard or custom PCB that simply closes a loop which will activate the triggers the cameras (3.5mm stereo cable). The loop is stereo so essentially will be in two stages, line 1 is focus line 2 is shutter. The focus loops for 1 second followed by shutter for 1 second.

Stage 1.1 Gyro function:

The trigger needs a tolerance factor so that it only is released when we are in a certain pitch and roll range, as we don't want to take photos whilst banking or climbing

Close loop if the following constraints comply (ignore my crude code)

int maxPitch = 3 // in degrees

int maxRoll = 5 // in degrees

1. Pitch =<maxPitch

2. Roll =<maxRoll

We also need a LED with red light or green light so we know if the system is level and ready to fire or in a status of pitch or roll.

Stage 1.2 GPS Trigger Function

The trigger will only fire when at a set GPS grid point, predetermined in a system. This part is hard to explain but not too difficult to apply if you you can think outside the square and know Math.

What I require is a static grid of gps points around the world that I would always refer to, evenly spaced 300m apart (if this number could be defined as an int that I could change later it would be awesome but not essential to get the ball rolling).

A generic grid means all the photos will be in the same spot to allow for me to update the database with new photos as the years go on.

If the GPS position is within say 50m of a point (also refined as an Integer) it will close the loop.

I am not a math expert, however I found a few ways of doing this by doing a google search. If the value matches one of the results of a math equation that gives us the 300m spacing then the loop closes. This also could be as a certain decimal spacing in the Lat / Lon cordinate. I.e. every .00267 degrees from 0. so S0.0 E0.0 becomes S0.00267 E0.00267, S0.00534, E0.00534. The only problem with this is the lng will change depending where you are latitudinally (the earth is a sphere).

We also need LEDs telling us when the GPS is within a distance that it can take photos. We do all our surveys along one of these Lat or lon lines, so essentially one will be on green if we are in the area needed, whilst the other flashes green as we pass the lines.

Stage 1.3 GPS Logging

Every time a trigger is activated, a time, date, altitude, and bearing is stamped onto an SD or Flash drive.

Stage 1.4 LCD (optional)

Have an LCD display instead of the LED's, including distance from closest point and current pitch and roll. This will allow us to know if we are going off the track we need to be travelling along, and how far to run until next point.

Stage 1.5 PCB

This trigger system implemented in a custom PCB (optional), no case needed.

C Programming Electronics Microcontroller PCB Layout Software Architecture

Project ID: #4290951

About the project

16 proposals Remote project Active Apr 7, 2013

16 freelancers are bidding on average $2469 for this job

MikroStar

hi, i am an electrical engineer and an embedded system developer. i can help you with this project.

$3000 AUD in 45 days
(60 Reviews)
7.7
MIKY4227

Hi see portfolio for similar project

$2000 AUD in 30 days
(53 Reviews)
6.6
deanosAU

Hi, I can help with this.

$2500 AUD in 60 days
(22 Reviews)
5.7
baobui

Hello. I can do it for you. Please check PM

$2500 AUD in 40 days
(11 Reviews)
5.6
sergeydm

Hello. I have 10+ years experience in hardware development (medium-high complexity) - circuit design, PCB routing-assembling, embedded software.

$3000 AUD in 60 days
(5 Reviews)
4.7
stemtechnologies

We will do the project using a custom built Cortex PCB with Gyro chip and gps module. We will do the pcb and test the hardware with camera and give you 2 working protos. REgards Soma

$3000 AUD in 60 days
(1 Review)
4.5
volansys

Hi, Please check your personal message box for more details. Regards, Volansys.

$3000 AUD in 25 days
(1 Review)
4.2
PavloT

I can do it.

$1500 AUD in 20 days
(7 Reviews)
4.4
eicr2013

Hi,I think I can do this

$1500 AUD in 25 days
(6 Reviews)
4.3
varticartur

Hi there! I can try to help you!

$1500 AUD in 20 days
(4 Reviews)
3.3
getveltrod

Hi, Veltrod Software services is a global software consulting company specialized in providing Mobile applications, Social media frameworks and eCommerce solutions. Leveraging best-in-class people, processes, and te More

$2500 AUD in 30 days
(0 Reviews)
0.0
cloudbit

Hello Sir, We are a company specialized in embedded systems development with more than 20 specialists in this field. We went through your project requirements and we left you a private message. We would gladly More

$2500 AUD in 30 days
(0 Reviews)
0.0
maksmusings

I can do it.

$1500 AUD in 20 days
(0 Reviews)
2.8
martingibbons

I have current experience using GPS trigger points and could progress this project

$2000 AUD in 40 days
(0 Reviews)
0.0
dmjtEngineering

We are the team of several engineers covering embedded HW and FW development, Linux device drivers and applications, and Java and Android stuff if needed. The price includes HW and PCB prototype interface board deliver More

$2500 AUD in 60 days
(0 Reviews)
0.0