
Closed
Posted
Paid on delivery
PCB Design for Industrial Burner Control Unit based on STM32G474RE We are looking for an experienced PCB designer to convert our working and client approved Burner Control Unit prototype into a production ready PCB. The firmware and control logic are complete and validated. We need a reliable, safety focused hardware design with isolated flame ionization sensing, thermocouple input, Modbus RTU communication and relay based valve and ignition control, suitable for an industrial enclosure. Hanyaa Auto Technologies has developed a Burner Control Unit for an industrial plant. The unit manages the complete burner sequence including prepurge, spark ignition, pilot flame proving through ionization sensing, main flame supervision, flame loss detection and post purge. The system has been demonstrated to the client and approved to move into PCB integration and enclosure development. The design must follow the intent of EN 298 for automatic burner control systems. Schematic capture from our existing prototype circuits and block level requirements Component selection review with focus on industrial grade and readily available parts in India PCB layout with proper separation of high voltage, mains, isolated analog and low voltage digital sections Creepage and clearance planning suitable for burner control safety requirements Low noise layout for the flame ionization sensing front end, which currently reads lower than expected on the prototype Design for manufacturing and assembly review Mechanical coordination so the board fits the enclosure we are developing Support during first prototype bring up and one design revision Main Circuit Blocks STM32G474RE microcontroller core with SWD programming header, crystal and reset circuit Flame ionization sensing using AMC3301 isolated amplifier with a transimpedance amplifier stage and INA228 power monitor on a dedicated I2C bus Single flame rod used for both spark and sensing, requiring careful protection of the sensing front end from the ignition pulse Ignition transformer control around 5 kV for approximately 3 seconds, switched through a relay Relay outputs for pilot gas valve, main gas valve, blower and alarm Thermocouple input using MAX31856, supporting multiple types including S and B selectable in firmware Character LCD on I2C with a front panel connector Modbus RTU over isolated RS485 Isolated power supply section for analog and communication domains Digital inputs for pressure switches, limit switches and reset button with suitable filtering and protection Status LEDs and test points for validation
Project ID: 40714809
30 proposals
Remote project
Active 2 hours ago
Set your budget and timeframe
Get paid for your work
Outline your proposal
It's free to sign up and bid on jobs
30 freelancers are bidding on average ₹10,646 INR for this job

Hi, I have experience in designing Circuits and can complete your project. I have expertise in the following: 1- Designing schematic and PCBA 2- Ordering the PCBA and getting boards manufactured. 3- Writing firmware for the PCBA to make sure everything works as expected. 4- I can also develop smartphone apps to communicate and control the hardware. If you wish we can discuss in chat. Thank you.
₹7,000 INR in 7 days
7.4
7.4

Drawing from over a decade's worth of experience in circuit design, electronics and embedded systems, I believe I am the right person for your Industrial Burner PCB Design & Optimization project. Hanyaa Auto Technologies' burner control unit aligns closely with my area of expertise, notably digital motor control and power electronics. Therefore, I'm more than proficient in using the STM32 microcontroller core in designing, programming and optimizing circuits to meet EN 298 standards. Creating optimized yet robust and reliable designs is always at the forefront of my mind throughout any project. My experience allows me to select industrial-grade components that are readily available within India without compromising on quality or safety. Furthermore, I thoroughly understand the significance of proper separation of high voltage, mains, isolated analog and low voltage digital sections - an aspect crucial for industrial enclosures like yours. Lastly, my proficiency in PCB layout encompasses mechanical coordination necessary to ensure a perfect fit with your upcoming enclosure design as well as supporting during prototype bring up. I also provide post-deployment support for one design revision, allowing a constructive space for further improvements. By working together, we can ensure your Burner Control Unit successfully transitions from prototype to production with a safe and reliable PCB. I look forward to discussing more details with you soon.
₹12,500 INR in 10 days
7.5
7.5

Hi there, I have carefully reviewed your requirements for converting the approved burner-control prototype into a production-ready STM32G474RE PCB with strong focus on safety, isolation, noise immunity, and industrial reliability. My experience covers STM32-based control systems, industrial PCB design, isolated analog sensing, thermocouple interfaces, RS485/Modbus, relay and solenoid control, protected digital inputs, isolated power domains, and high-voltage/low-voltage segregation. I have already worked with the main technologies involved in this project, including STM32, AMC3301-class isolation, MAX31856 thermocouple interfaces, I2C peripherals, RS485, relay drivers, flame/low-level analog sensing, and industrial protection circuits. I can handle schematic capture from the existing prototype, component review, PCB layout, creepage/clearance planning, flame-sensing front-end optimization, ignition-pulse protection, DFM/DFA review, enclosure coordination, and first-prototype bring-up support. Particular attention will be given to the single flame-rod ignition/sensing path and the low-noise analog section. Given that the firmware and control logic are already validated, I can move quickly toward a robust production design aligned with the intended EN 298 safety requirements. Send me a message with the existing prototype documentation and mechanical constraints, and I can start immediately. Best regards, Samuel tshibangu
₹12,500 INR in 1 day
6.5
6.5

As an expert in PCB design and optimization with over 8 years of experience, I am confident that my skills and knowledge will prove to be invaluable for your Industrial Burner PCB Design & Optimization project. My extensive experience using Eagle, Altium, KiCAD, and EasyEDA for designing high-quality circuit boards aligns perfectly with your requirement for schematic capture and board layout. My professional portfolio will also assure you of my proficiency in handling complex tasks such as designing hardware with isolated flame ionization sensing, thermocouple input, Modbus RTU communication, and relay based valve and ignition control, features your project distinctly needs. Safety being a key concern in burner control systems, I have been diligent in adhering to safety standards like EN 298 in my designs to create reliable solutions that minimize risks. In addition to my technical expertise, I am recognized as a Preferred Freelancer within the top 1% of skilled professionals. This recognition is a testament to my commitment to provide high-quality solutions within stipulated timelines. I am dedicated to turning your vision into reality and ensuring the success of your project at every step. Choosing me means choosing reliability, quality and an unwavering focus on your project's specific requirements. Let's collaborate to create a production-ready PCB design that exceeds your expectation!
₹7,000 INR in 7 days
6.7
6.7

Hey there! I’m Alok, A PCB, Circuit and Mechanical designer with a passion for turning ideas into rock-solid, high-performance circuit boards. even expert on Python, C, C++ With nearly a decade of experience, I’ve tackled everything from compact consumer gadgets to complex industrial systems—always with a focus on precision, efficiency, and reliability. # Schematic & Layout Design – Clean, optimized, and manufacturable. # Component Selection & Library Management – No surprises, just the right parts for the job. # Reverse Engineering – PCB cloning, replication, and improvements. # Gerber, BOM & CPL Generation – Ready for seamless production. # DFM & DFA Expertise – Because great design means smooth manufacturing. # Multi-Layer, Flex, & High-Density PCB Design – Whatever the project needs. If you need a PCB and Code that’s efficient, reliable, and built for real-world performance, let’s chat. I’d love to help bring your project to life!
₹7,000 INR in 7 days
5.9
5.9

As a highly skilled and experienced PCB designer, I'm confident in my ability to deliver the exacting requirements you need for your Industrial Burner Control Unit. My comprehensive understanding of EN 298 and experience in developing automatic burner control systems makes me a perfect fit for the detailed work your project demands. Having designed and manufactured various safety-critical hardware systems, my expertise lies in creating reliable and robust circuit layouts for industrial environments, while ensuring proper isolation of different sections and adhering to appropriate creepage and clearance specifications. Additionally, I've previously integrated STM32 microcontrollers, Modbus communications, thermocouple input, and relay-based controls -- so rest assured, I understand the complexity of this project. Further, your project's need for flame ionization sensing with low noise layout is something I have personal experience optimizing. With meticulous attention to detail, I can eliminate the low reading issue you've observed on your current prototype. My commitment to design integrity combined with my knowledge of local component availability will also ensure a highly functional yet cost-effective PCB design solution compliant with your industrial enclosure dimensions.
₹6,700 INR in 1 day
5.9
5.9

As an electrical engineer with a strong background in circuit design and industrial applications, I am confident that my skills and experience align perfectly with your project needs. Over the years, I have successfully designed and implemented several complex PCBs, often for safety-sensitive industrial applications. Safety is one of the prime factors in projects involving high voltage and ignition control like yours, and you can count on me to meticulously adhere to every applicable safety standard to ensure flawless operation. Having extensively worked on STM32 processors, I am well-versed with its architecture and can expertly handle the STM32G474RE microcontroller core at the heart of your system. Likewise, I am experienced in designing with flame ionization sensors such as the AMC3301 isolated amplifier you've specified, ensuring both precision and safety measures are met. My familiarity with thermocouple inputs using devices like MAX31856 will also prove invaluable in designing your burner control unit.
₹1,566 INR in 1 day
5.3
5.3

Hi, Greetings! I am interested in working on your project. Please share the design details, specifications, and project requirements so we can discuss them further. I look forward to working with you. Thank you. Shivkant Verma
₹25,000 INR in 7 days
4.7
4.7

I am an Embedded Systems and PCB Design Engineer with experience in Altium Designer, Kicad, Easyeda, Protious and custom hardware development. I can design your PCB from schematic to production-ready files, including: • Schematic Design • PCB Layout • Component Selection • Design Rule Check (DRC) • Gerber Generation • BOM Preparation • Manufacturing Support (JLCPCB, PCBWay, etc.) I have experience with ESP32, STM32, sensor interfaces, power supplies, RF modules, Ethernet, and industrial electronics. Please share the project requirements, schematic (if available), board dimensions, and any special requirements. I can start immediately. Looking forward to working with you.
₹15,000 INR in 8 days
5.0
5.0

Hello, I have carefully reviewed the project details and requirements. I understand the key challenges, especially the STM32G474RE controller, isolated flame ionization sensing, thermocouple input, isolated RS485/Modbus RTU, relay outputs, and the required separation between HV, mains, analog, and digital sections. I have solid experience with STM32-based controller boards, schematic design, component selection, and PCB layout. I pay close attention to protection, isolation, creepage/clearance, noise reduction, and manufacturing requirements. I would also give special attention to the flame ionization sensing circuit and its low reading on the prototype, particularly its layout and protection from the 5 kV ignition pulse. Please feel free to check my portfolio for similar controllers and PCB projects. I’d be happy to review your existing prototype and take it through PCB layout, prototype bring-up, and the required revision. Best regards, Ahmed
₹7,000 INR in 7 days
4.5
4.5

Hi, I’m an experienced Hardware/PCB Design Engineer with strong STM32, industrial IoT, schematic and production PCB design experience. I can convert your approved Burner Control Unit prototype into a production-ready PCB, focusing on HV/LV isolation, creepage/clearance, low-noise flame sensing, RS485 isolation, DFM and enclosure fitment. I can also support prototype bring-up and revision. Note: 1. Bid price not included for PCB manufacturing component procurement and and Assembly. 2. Complete support for prototyping bring-up and revision. Ready to work start immediately. Let's discuss about the project work.
₹8,600 INR in 18 days
4.1
4.1

You already have the validated control logic—now the challenge is turning it into a safe, production-ready burner control PCB. I can convert your approved prototype into a robust STM32G474RE-based PCB, with particular attention to isolation, creepage/clearance, flame-sensing noise performance, ignition-pulse protection, and clean separation of mains/HV, analog, isolated and digital domains. I’ll cover: • Production schematic capture from your prototype • Industrial-grade, India-available component selection • Low-noise AMC3301 + TIA flame sensing redesign/layout • MAX31856 thermocouple interface • Isolated RS485/Modbus RTU and power domains • Relay control for valves, blower, alarm and ignition • HV/mains creepage & clearance planning • Input protection, filtering, test points and diagnostics • DFM/DFA and enclosure/mechanical coordination • Manufacturing-ready PCB/Gerbers + BOM • Prototype bring-up support and one revision I understand the single flame-rod requirement and the need to protect the sensing front end from the ~5 kV ignition pulse. I’ll also design with the stated EN 298 intent and safety requirements in mind, while leaving formal compliance certification to the appropriate testing body. Send the existing prototype schematic/PCB files and enclosure constraints, and I can start from the validated design rather than rebuilding the system logic. Best Regards, Sumit Kumar.
₹4,500 INR in 1 day
4.4
4.4

Hi, I can convert your approved STM32G474RE burner-control prototype into a production-ready PCB with strong focus on safety, noise immunity, isolation, DFM, and enclosure integration. I can handle: • Full schematic capture from prototype circuits • STM32G474RE core + SWD/reset/clock • AMC3301 flame-ionization sensing front end • Protection for shared spark/flame rod path • Low-noise TIA/analog routing optimization • MAX31856 thermocouple interface • Isolated RS485 / Modbus RTU • Relay outputs for ignition, valves, blower and alarm • Isolated power domains • Protected digital inputs • Creepage/clearance planning for mains/HV sections • Test points and status LEDs • Enclosure/mechanical coordination • ERC/DRC + DFM review • Gerbers, drill, BOM, Pick & Place and assembly files • One revision after prototype bring-up I’m comfortable with STM32, mixed-signal PCB layout, isolated analog sensing, industrial I/O, RS485, relay drivers, high-voltage separation, and production documentation. I’ll first review your prototype schematic, measurements, enclosure constraints, ignition circuit and existing flame-sense performance, then optimize the final layout around those verified interfaces. Best regards Ankit
₹7,000 INR in 1 day
3.9
3.9

Your ionization front end reading low is almost certainly a layout and grounding issue, not the AMC3301 itself — that stage is very sensitive to creepage, return paths and ignition pulse coupling, so I would fix it at the schematic and stackup level rather than in firmware. Here's what I bring to this: → I have shipped STM32G474-based industrial boards with isolated analog front ends, Modbus RTU over isolated RS485 and relay-driven valve control, including a cold storage monitoring system built on ESP32 with Matter protocol that runs 24/7 in the field. → Firmware, PCB, 3D enclosure design and full prototype shipping all sit with me, so mechanical coordination with your enclosure happens in parallel with layout, not after it. → I work in KiCad and Altium, and I keep creepage/clearance planning for mains and isolated domains as a first-class part of the stackup, aligned with EN 298 intent. My approach: → Schematic capture from your validated prototype circuits, then a component review focused on industrial-grade parts with reliable Indian supply.
₹8,000 INR in 3 days
3.5
3.5

I have extensive experience with STM32-based industrial control systems, isolated analog front ends, RS485 communications, power electronics, and safety-focused PCB design. This project aligns well with my background in industrial IoT and mixed-signal hardware development. For your Burner Control Unit, I can convert the validated prototype into a production-ready PCB while focusing on flame sensing integrity, high-voltage ignition isolation, relay control reliability, and manufacturability. I am familiar with creepage/clearance requirements, isolated communication interfaces, low-noise analog layout techniques, and industrial protection methods for ESD, surge, and switching transients. Particular attention will be given to the shared flame rod architecture, ensuring adequate protection between the ignition pulse path and the ionization sensing circuitry. I can support schematic review, component optimization, PCB layout, DFM checks, prototype bring-up, and design revision.
₹12,000 INR in 7 days
3.6
3.6

Your burner control unit sounds like a serious, safety-critical build — and I noticed the flame ionization front end reading lower than expected on your prototype, which is usually a layout and isolation issue I'd tackle first. → I've designed isolated analog front ends with AMC3301 and INA228 on STM32G474-class hardware, so the flame sensing and Modbus RTU blocks are familiar ground. → I'll handle schematic capture, creepage and clearance planning to EN 298 intent, high-voltage and isolated analog separation, plus DFM review. → Firmware, PCB, 3D enclosure design and prototype shipping all sit under one roof, so the board fits your enclosure without back-and-forth. → First schematic review in about a week, with bring-up support and one revision included.
₹7,000 INR in 7 days
3.0
3.0

Hello, I can convert your validated Burner Control Unit prototype into a production-ready PCB with a strong focus on safety, isolation, EMC, and manufacturability. I understand the critical architecture: STM32G474RE, AMC3301 isolated flame-ionization sensing with TIA, MAX31856 thermocouple interface, isolated RS485/Modbus RTU, relay-controlled gas valves/blower/ignition, isolated power domains, and protected digital inputs. My approach would include: * Schematic capture and review from your validated prototype * Industrial-grade, readily available component selection * Creepage/clearance and physical separation of HV/mains, relay/ignition, isolated analog, and digital sections * Low-noise layout for the flame sensing front end * Protection of the sensing circuit against the shared 5 kV ignition pulse * Proper isolation, grounding, filtering, and EMC-conscious routing * DFM/DFA and assembly review * SWD, test points, and prototype validation access * Mechanical coordination with your enclosure * Support during first prototype bring-up and one revision The flame-ionization section and shared spark/sensing path are areas I would review carefully, especially since the prototype currently shows lower-than-expected sensing levels. Please share the prototype schematics, BOM, PCB/mechanical files, and enclosure dimensions. I can review them first and proceed with the PCB integration.
₹6,500 INR in 7 days
0.6
0.6

Hi, The flame ionization front end is the part that'll make or break this board a single rod doing double duty for spark and sensing means the AMC3301 stage needs real isolation from the ignition pulse, not just distance on the layout. I'd start there: rework the transimpedance stage and grounding so the noise you're seeing on the prototype actually goes away, then build the rest of the layout around clean separation of mains, isolated analog, and low-voltage digital. I'll take your schematics and block requirements through to a production-ready layout proper creepage/clearance for the mains and ignition sections, isolated RS485 for Modbus, MAX31856 thermocouple input, relay outputs for valves/blower/alarm, and mechanical fit to your enclosure. Component selection reviewed for industrial-grade parts available in India. I'll follow EN298 intent throughout, especially around the flame supervision and shutdown paths.
₹1,500 INR in 1 day
0.0
0.0

Hello, Your product is classic industrial requiring safety, robustness, EMI-EMC considerations. Your product needs careful isolation between ignition transformer, mains, isolated RS485 & sensitive analog circuit. It needs careful review of minimum industrial immunity requirements as per IEC 61000-X-X along with needed creepage/ clearance. I shall review your schematic for missing protections along with your functional circuit. Apart from this I shall review your PCB from thermal perspective. Will render layout having suitable isolation at component levels, safety requirements & mass production friendly. With 20+ years of practical circuit design & hands on in analog, EMI-EMC, safety, Low Power IoT, I can suitably handle your project. Please see my profile, https://www.freelancer.in/u/JagdishCK Queries, 1. What are the dimensions of the product you are looking for? 2. Do you have details of creepage or clearance gaps? Please message me for discussion & queries on this project. Regards, Jagdish Karamchandani
₹45,000 INR in 25 days
0.0
0.0

hello, thanks for checking my proposal. I understand the main goal is to take your already working STM32G474RE burner controller and turn it into a safe, production-ready industrial PCB, without changing the validated firmware or burner sequence. The critical part is getting the isolation, high-voltage separation, flame sensing, and protection right, especially around the 5 kV ignition and the low-level ionization signal. I can rebuild the prototype circuits into a clean schematic and PCB, separating mains/HV, analog sensing, isolated RS485, and digital control sections with proper creepage and clearance. I’d pay particular attention to the AMC3301 flame-sensing front end, ignition-pulse protection, isolated supplies, MAX31856 thermocouple input, relay outputs, and DFM/test points. I can also support the first board bring-up and one revision after testing.
₹8,000 INR in 5 days
0.0
0.0

Tirupati, India
Member since Sep 16, 2026
₹1500-12500 INR
₹12500-37500 INR
$1500-3000 USD
$30-250 USD
$750-1500 USD
₹12500-37500 INR
₹12500-37500 INR
£250-750 GBP
₹1500-12500 INR
$300-400 USD
$30-250 USD
£18-36 GBP / hour
€30-250 EUR
$30-250 NZD
$250-750 USD
£250-750 GBP
$1500-3000 USD
£250-750 GBP
$30-250 USD
$250-750 USD