Write an Arduino Program

Hi, I made my search on FL05 and ADXL335 and I got useful information. We could discuss more via chat. I believe that I can do your job very fast and perfectly. Contact me to discuss more details, please.

Hello, thank you for your job posting. I read your description about--ARDUINO CODE I am a senior electrical engineer. I have plenty of experience in firmware development and micro-controller developments. I can write the firmware based on Arduino, Raspberry Pi, Pic, Atmega, FPGA, ARM, DSP, PLC and so on. And I can design the circuit by the Altium, Eagle, KiCAD, Allegro & OrCAD, PADs. I provide the services - Gerber files, Netlist generation, BOM generation and 3D Models of PCAD and ECAD. I am also good at AutoCAD, Solidworks. And I can simulate all circuits with Proteus, LT-spice, Matlab, Simulink, Multisim, and Labview as well. Due to my experience in firmware development, I will bring you the perfect result in time with high quality. I will also give you a detailed explanation of the process. Looking forward to hearing from you soon Thanks

Hi. I am a professional Arduino programmer with rich experience over 10 years. I have read your project description very carefully and I will finish it in a short time perfectly. Please let me discuss about your project in detail. Best regards, Andrii.

As far as I understand, your tank (conteiner) will move. In that case I would recommend to use MPU6050 instead of ADXL335 - that will provide more precise and reliable measurement of tilt. I have made more than 200 Arduino-based projects on different freelance stocks. I work with Arduino since 2010 and have more than 25 years of experience in programming and electronics. Also, I have made a custom library for SIM800/900 devices that was tested on many projects and was created for unattended devices. Please feel free to contact me in chat

Am full-time freelancer expert in Electrical & Electronic Circuit Designing & Simulation, PCB Designing, Consultancy of different types of Electrical & Electronic Problem. I have worked on both Arduino, Verilog and Bitstream FPGA for bc1525. It will be my joy to work on your project. Kindly share more details with me via chat

hello dear project owner i am an electronic engineer with experience in embedded system designing and pcb designing. i can help you in your project and can complete it in minimum time.

Hey there, We are a team of young ELECTRONICS ENGINEERs, PROGRAMMERs, and MECHANICAL ENGINEERs. We got the overview of your project and we are interested in working with you We can design you a highly precise, robust, and cost-effective system as per your requirement, We strictly follow the product development life cycle, real-time analysis, and testing procedures, We work to deliver satisfactory results on time. From 4 years we are developing products from scratch hence we have a reliable Workforce, Skills, Tools, and Enthusiasm to provide state of the products and engineering solution and products We would really to talk about this project in details please spare a minute to talk with us in the inbox. below are the key services we provide. 1. CIRCUIT DESIGNING and PCB LAYOUTS DESIGNING. 2. DESIGNING AND DEVELOPMENT of the CYBER PHYSICAL DEVICES 3. DEVELOPMENT OF FIRMWARE FOR MICROCONTROLLER SYSTEMs. 4. WINDOWS, ANDROID, AND LINUX(Raspbian)APP DEVELOPMENT. 5. MANUFACTURING of PCBs. NOTE - Our bid price may be expensive, But we will offer services and enthusiasm for this project it will be definitely worth paying for it. SMB technologies are always open and ready to face challenges, explore new things, learn new technologies, and compete with leading potentials. Thank you SMB technologies.

Hello ...................................................................................................................................

Hello.. I am holding masters degree in electrical and electronics engineering.. I have very good experience in microcontrollers programming.. I have gone through your requirements and I am sure that I can do this project perfectly.. Kindly drop me a message through chat.. Then we can discuss further and start the work right now.. Looking forward to hearing from you soon.. THANKS

Done similar projects using Arduino. I have more than 8 years of academic and research experience in Microcontroller, Arduino. Looking forward for your positive response.

Hi I read your request and very excited on your project. A few weeks ago, I had completed an similar project with yours. That was to create a GPS logger with ESP32 with encrypted SD storage and ESPNOW data transfer. The rate of GPS logging had to be easily configurable, and the ESP had to go into low power sleep mode when no movement. Movement will be detected by a tilt sensor or similar. The GPS logger had to listen for incoming transmission of ESPNOW from a second 'Receiver' device, when the receiver was detected it had to transmit the encrypted GPS log files by ESPNOW to the receiver and clear the SD card. This project was made perfectly and it is working now without stopping. So I am sure I can do your request in a short time and perfectly and I will be glad if you give me a chance to work on your request. Looking forward to hearing from you. Sincerely. Nick

Hi, I have 15 years’ experience in development I have read your project description and I’m confident I can do this project for you perfectly. I only bid on jobs. I am 100% confident I can complete on time& on budget. Please leave a message on my chat so we can discuss the budget and deadline of the project. I am very prompt in communication and always prefer to discuss the project on call/chat and finalized the cost of the project. I believe giving suggestions and asking question to deliver stable & quality final product. I am very interested to work with you. Please let us know when we can start the project Thanks,

hello sir.✋ I have just read your job description and your project is really interesting to me. The Items you raised are similar to what I have already done in practice and I think you can do it in a short time if you have a little explanation. I'm an expert having specialization in Electronic Engineering Design. ✔️ Embedded system based on Microcontroller (ATMEGA, AVR, STM8, STM32, MSP430, TMS320, PIC ...) ✔️ Python with Deep Learning, Machine Learning ✔️ Python with Data Science ✔️ A system based on development boards(Arduino, Raspberry PI, Node MCU, Bluechip, Teensy,…) ✔️ Antenna design & Analog circuit/RF communication circuit designing and simulation using Proteus, P-Spice, Tina Pro, ADS, CST, Ansys, HFSS ✔️ Bluetooth, WIFI, zigbee, LoRA ✔️ High-Speed layout using HyperLynx ✔️ PCB layout designing, providing GERBER and BOMs, 3D files using Altium, EAGLE, Kicad, EasyEDA… ✔️ Programming firmware of Microcontroller & C++ ✔️ BMS I think my many design and practical experiences can help you design your project and give you enough satisfaction. I look forward to your response. Best Regards.

Hello there, I am an expert mechanical engineer with experience in programming of Arduino boards. I have read and understood the project requirements and will start immediately if contacted. Please contact me for quality and timely service.

I am an Electronics and Communications engineer and have a good experience with Arduino Uno and sensors interfacing. I have worked with GPS, Capacitance sensors too.